November 10, 2026
Your project is ready to swap a worn DN300 butterfly valve. The new unit arrives, the crew lines it up, and the flanges miss by tens of millimeters. The short-pattern valve you ordered will not drop into the long-pattern gap left by the old body. Nothing is wrong with the disc, seat, or pressure rating—the mismatch is valve face to face dimensions.
When buyers talk about valve FTF dimensions, they mean the axial length the valve occupies between the connecting pipe ends. That number decides whether your spool fits, whether a replacement drops in, and whether two manufacturers can interchange without cutting steel. Treat FTF as a measured, standard-bound dimension—not a guess from nominal size alone.
Face-to-face (FTF) is the distance between the two flange sealing faces on a flanged valve, measured along the valve axis. End-to-end (ETE) is the matching idea for butt-weld valves: the distance between the two weld ends. Datasheets and isometrics use these terms so fabricators and inspectors share one length. If your RFQ mixes FTF language with weld-end valves, suppliers may quote the wrong geometry even when DN and pressure class look correct.
Three related terms show up on drawings, and mixing them causes wrong stock. FTF applies to through-line flanged valves. ETE applies to butt-weld ends. Center-to-face (CTF) applies to angle-pattern valves: you measure from the run pipe centerline to the branch flange face. Wafer valves sit apart: a wafer body has no integral flanges, so its FTF is the body thickness clamped between the two pipeline flanges. Lug bodies may share a similar envelope while offering tapped lugs for one-side removal. When you compare a wafer butterfly valve with a flanged pattern, confirm whether the published length is body thickness or full flange-to-flange length.
| Term | Applies To | What You Measure |
|---|---|---|
| FTF (Face-to-Face) | Flanged through-line valves | Sealing face to sealing face |
| ETE (End-to-End) | Butt-weld valves | Weld end to weld end |
| CTF (Center-to-Face) | Angle-pattern valves | Pipe centerline to flange face |
| Wafer FTF | Wafer / many lug butterflies | Body thickness between pipe flanges |
Nominal diameter alone never fixes length. A DN300 valve can be short pattern or long pattern under EN 558, or follow a different structural length under ASME B16.10. Measure the installed gap on site when replacing an unknown legacy valve, and read the standard series on new builds. Guessing from DN invites the short-versus-long miss that stranded your DN300 change-out.
On a new rack you can still adjust spool length in fabrication. On a live plant you usually cannot. Retrofit jobs inherit the face-to-face already bolted or welded into the line. If the new valve is shorter, the flanges will not meet without a spool piece or pulled pipe. If it is longer, the crew cannot close the joint without cutting and re-beveling. Your business pays for either path in labor, hot work permits, and downtime—not in the valve invoice alone.
Interchangeability rests on shared standards and shared series. When two makers both supply DN300 PN16 EN 558 Series 14 flanged butterflies, their face-to-face lengths align, so you can swap brands without re-piping. That is the practical meaning of a butterfly valve face to face standard. Cross-standard swaps are different: moving from an EN 558 long pattern to an ASME B16.10 length, or from ISO 5752 face to face short pattern to a U.S. Class-rated envelope, often changes axial length at the same DN. Same size on the purchase order does not mean same gap in the pipe.
Wrong length forces mechanical work: adding a spool piece, trimming a pup, or cutting and rewelding flanges. Each option adds fabrication hours, inspection, and schedule risk. Specifying the correct valve FTF dimensions up front is cheaper than discovering the miss on the pad.
Confirm Before You Order
Share your DN, pressure rating, standard series, and end type so the quoted length matches the installed pipe gap.
Procurement teams usually work inside two families. The European system centers on ISO 5752 and EN 558 for face-to-face lengths of industrial valves—including butterfly, gate, and globe patterns—broken into series such as F1, F4, F5, and F16 for short and long envelopes. The American system centers on ASME B16.10 for flanged and butt-welding end valve structural lengths. Pipeline ball and gate valves may also reference API 6D overall lengths. Pick one system for the piping class and stay inside it unless engineering redesigns the spool.
ISO 5752 face to face tables and EN 558 series define basic lengths by DN and series number. Butterfly valves commonly use short and long patterns within those series, plus wafer series across water, HVAC, and process lines. When your datasheet cites EN 558 Series 14, every compliant supplier targets that same basic dimension. Citing only “DIN butterfly” or “ISO length” without the series leaves length ambiguous.
ASME B16.10 lists face-to-face and end-to-end dimensions for flanged and butt-weld gate, globe, check, and many ball valves by NPS and pressure class. API 6D covers pipeline valves and may specify overall lengths that differ from a general industrial butterfly table. If your plant mixes EN-rated water lines with ASME Class process headers, tag each line’s FTF system so warehouses do not issue the “same DN” from the wrong rack.
| Common Butterfly Pattern | Typical Reference | What Buyers Should Confirm |
|---|---|---|
| Flanged short pattern | EN 558 short series (e.g. Series 13) | DN, PN, series number, flange facing |
| Flanged long pattern | EN 558 long series (e.g. Series 14) | Match installed long gap on retrofits |
| Wafer pattern | EN 558 wafer series (e.g. Series 20) | Body thickness vs flange-to-flange FTF |
| ASME flanged industrial valve | ASME B16.10 by NPS and Class | Do not assume EN length equals Class length |
Butterfly valves are where short-versus-long mistakes show up most often. Short-pattern bodies save space and weight; long-pattern bodies match older installs and some isolation layouts. Both can be valid under ISO 5752 / EN 558 rules, yet they are not interchangeable at the same DN. When you replace a legacy long-pattern flanged butterfly valve, order the matching long series—or budget for a spool. Wafer and lug butterflies usually publish a compact wafer face to face thickness rather than a double-flange length, so verify end type as well.
Gate, globe, and many flanged ball valves lean on ASME B16.10 in Class-rated piping, or on EN 558 series in PN-rated European piping. An ASME B16.10 gate valve face-to-face from an ASME Class 150 table will not automatically equal a PN16 EN series length after a soft DN-to-NPS conversion. Pair the valve type with the governing length standard in every RFQ line item.
Wafer valves clamp between companion flanges; flanged valves bring their own flange faces. That difference changes how you read FTF on the drawing and how you set gasket stacks. If your team is choosing between wafer and lug constructions, review the install trade-offs in a dedicated wafer vs lug comparison, then lock the face-to-face number that matches the chosen body style before fabrication releases holds.
Your RFQ line should carry DN or NPS, PN or Class, the standard number, and the series or table identity—for example DN300 PN16 EN 558 Series 14. Add end type (wafer, lug, double flanged, butt-weld) and facing (RF, RTJ) so the supplier cannot substitute another envelope. Writing only “DN300 butterfly valve” invites a short-pattern quote into a long-pattern hole. If vendors mix Class and PN language, clarify pressure class versus PN before you compare lengths.
RFQ Face-to-Face Checklist
Standards publish a basic face-to-face dimension with an allowed tolerance. Manufacturers machine to that basic length; inspectors check it on incoming goods. Record the basic dimension and tolerance on datasheet approval, then measure critical replacements on site when the legacy tag is missing. For tight racks, confirm whether the tolerance stack with gaskets still closes without pulling pipe.
Buyers sometimes assume an ISO 5752 / EN 558 butterfly length equals an ASME B16.10 gate or ball length after a soft DN-to-NPS conversion. Those tables serve different valve families and pressure systems. Another trap is treating API pipeline end-to-end figures as if they were EN butterfly series lengths. Keep European FTF series and American structural-length tables in separate columns on your takeoff.
DN300 is a size, not a length. Short pattern, long pattern, wafer thickness, lug, and double-flanged bodies can all appear at DN300 with different axial envelopes. Stock rooms that bin only by DN will issue the wrong valve under time pressure. Tag inventory by DN plus standard plus series plus end type so your night shift cannot grab “any twelve-inch butterfly.”
No reliable one-to-one conversion exists for procurement. The tables are independent. Buy to the system on your isometric, or have piping redesign the spool and update stress checks.
Engineering should freeze the required standard and series from as-built drawings or a field measurement. Purchasing then enforces that string on the PO and rejects length-changing alternates. Splitting ownership without a written basic dimension is how short-pattern valves reach long-pattern flanges.
The valve’s standardized face-to-face dimension is separate from the gasket and flange joint dimensions. However, gasket thickness, facing type and joint design can affect the final installed piping arrangement. These factors should be considered when designing or modifying pipe spools, especially in tight installation spaces. On tight fits, include gasket make-up before cutting a new spool.
Not without a numeric basic dimension and a redline to the isometric. Marketing equivalence does not replace EN 558 or ASME B16.10 identification. Ask for the standard clause, series or table, and a dimensional drawing before you approve the alternate.
Measure sealing-face to sealing-face or weld end to weld end on the removed valve or open flange gap, photograph the setup, and record DN, end type, and facing. Map that measurement to the nearest standard series with engineering sign-off rather than rounding to a catalog page.
Actuator mass does not change FTF itself, but a heavier operator can change support needs beside a short spool. Keep FTF and supports as separate checks so an operator upgrade does not hide a length mistake.
Valve face to face dimensions decide whether your replacement bolts in or turns into cut-and-weld work. Define FTF, ETE, CTF, and wafer thickness clearly, stay inside one standard family, and write DN, pressure rating, standard, and series on every RFQ. Measure legacy gaps when tags are gone.
Lock DN, Series, and End Type on Your RFQ
Send your line list with EN 558 or ASME B16.10 series before the PO lands, so the envelope matches on site.
Privacy Policy | SiteMap Copyright Tianjin Dingliu valve Industry Co., Ltd.