...

Nuestro sitio web utiliza cookies para mejorar su experiencia y registrar estadísticas de uso. Al utilizar nuestro sitio, usted acepta las cookies como se describe en nuestra Política de privacidad. Nos tomamos muy en serio su privacidad y la seguridad de sus datos y toda la información recopilada se mantendrá estrictamente confidencial.

Rechazar todo Aceptar todo

Diferencia entre válvula de retención de golpe y no golpe

2 de septiembre de 2026

Imagínese esto en sus instalaciones: una bomba centrífuga se activa en medio de la noche y, un segundo después, un ruido metálico amortiguado resuena a través de la línea. La pared de la tubería vibra, la aguja de un manómetro se mueve y un accesorio en algún lugar aguas abajo no sobrevivirá a otros cientos de esos eventos. Ese golpe es el disco de un válvula de retención golpeando su asiento mientras el flujo inverso intenta avanzar: un caso de libro de texto de golpe de ariete. Si no se soluciona, su negocio se verá afectado por asientos agrietados, pasadores cortados, juntas con fugas, bandas verticales rotas y paradas no planificadas.

Esta guía guía a su equipo exactamente por qué una válvula de retención estándar se cierra de golpe, cómo un diseño que no golpea elimina ese impacto, el cuatro estructuras que los ingenieros realmente usan para detenerlo, y cuando su aplicación realmente necesita una válvula de retención antigolpes en lugar de una convencional. Al final, podrá elegir la válvula adecuada para su bomba, calcular el aumento repentino al que está expuesto su sistema e informar a su equipo de adquisiciones con confianza.

Rubber Disc Check Valve

¿Qué es una válvula de retención de golpe?

Primero, una aclaración importante para su hoja de especificaciones: “La ”válvula de retención de golpe” no es una clasificación formal de válvula.. Es el término que utilizan los ingenieros cuando se utiliza una válvula de retención ordinaria (más a menudo una válvula de retención). swing check valve — se cierra de golpe al invertir el flujo. En otras palabras, “slam” describe un comportamiento La válvula se exhibe, no es un tipo que pueda pedir.

Cómo se cierra una válvula de retención oscilante al caer el flujo

Una válvula de retención oscilante tiene un disco articulado en la parte superior del cuerpo. Si bien el flujo hacia adelante es saludable, el disco se abre y se apoya contra un tope. En el momento en que la velocidad de avance cae por debajo de la presión de agrietamiento del disco, el disco comienza a cerrarse. Críticamente, sólo termina de cerrarse cuando contrarrestar El flujo comienza a empujarlo hacia el asiento. Por lo tanto, el disco se cierra contra una columna de agua que ya está invirtiendo: una receta para el impacto.

Por qué ocurre el Slam cuando una bomba se dispara repentinamente

Cuando la bomba se dispara, se corta la energía al impulsor, pero la columna de agua en la línea de descarga sigue moviéndose durante una fracción de segundo. Esa columna móvil invierte, acelera y golpea el disco contra el asiento. La energía cinética se convierte en un pico de presión, el golpe de ariete, que viaja a la velocidad del sonido en el fluido (aproximadamente 1200 m/s en una tubería de agua de acero). Ese aumento es lo que agrieta los asientos, corta los vástagos y revienta los accesorios. Cuanto más rápida es la línea, más larga es la columna y cuanto más repentina es la parada, más grande es el pico.

¿Elegir una válvula de retención para una línea de bomba crítica?

Envíenos el tamaño de su línea, clase de presión, fluido y ciclo de trabajo; nuestros ingenieros le recomendarán el diseño antigolpes adecuado.

Hable con un especialista en válvulas de retención →

¿Qué es una válvula de retención sin golpe?

A válvula de retención antigolpes ¿Hay alguna válvula de retención diseñada para que el disco se cierre? before reverse flow can build up. Instead of waiting for the returning column of water to push the disc onto the seat, the valve starts closing proactively — the moment forward velocity begins to decay. By the time reverse flow arrives, the disc is already on (or very near) the seat, so the closing energy is dissipated as controlled friction rather than as a pressure spike.

Cómo el mecanismo de amortiguación previene el impacto

Every non-slam design uses the same basic idea: close early, close slowly, or both. A spring, a damper, a streamlined flow path, or a hydraulic dashpot does the work of bringing the disc home gently. The energy that would have become a pressure surge is instead absorbed by the closing mechanism, the seat, and the fluid itself. The result: no slam, no water hammer, no bang at 3 a.m.

Cuatro estructuras convencionales de Non-slam que su equipo debe conocer

In real pumping systems, your business will encounter four families of non-slam construction. Each addresses the slam problem in a different way:

  • Spring-assisted swing check. A torsion or compression spring tugs the disc toward the seat as forward flow decays, so it closes early instead of waiting for reverse flow to do the job.
  • Dual-plate (wafer) check valve. Two half-discs hinged on a central pin fold closed over a very short stroke; a pair of torsion springs snaps them home quickly but softly, which is why a dual plate check valve is a common choice in compact, light-weight systems.
  • Axial-flow / silent check valve. The disc travels along the pipe axis through a streamlined flow path, assisted by a spring; this is the design engineers reach for when both low pressure loss and low acoustic signature matter.
  • Slow-closing (damped) check valve. A hydraulic oil dashpot decelerates the disc over the final portion of its stroke, eliminating the last bit of impact velocity even on very long, high-velocity lines.

Silent ≠ Non-slam: una aclaración que evita costosos errores de especificación

Procurement teams frequently use silent y non-slam as if they mean the same thing. They do not. A silent check valve is defined by its acoustics — it is engineered to suppress fluid-borne noise by routing flow through a streamlined, axial passage. A válvula de retención antigolpes is defined by its closing dynamics — it is engineered to eliminate the disc-on-seat impact that drives water hammer. Some designs — notably axial-flow valves with a strong return spring — deliver both, and a slow-closing (damped) check valve can be made very quiet as well. But when you specify, write down which of the two you need: noise control, surge control, or both. Conflating them is how your business ends up with a “silent” valve that still hammers.

Una válvula de retención silenciosa azul diseñada para evitar el ruido y reducir el golpe de ariete.

Unsure whether your system needs silent, non-slam, or both?

Share your line profile and operating duty — we will map it to the correct structure and quote you a matched non-slam slow-closing or silent check valve.

Request a recommendation →

Slam vs Non-Slam Check Valve: 5 Key Differences

When your business is weighing a standard check valve against a non-slam model, these are the five engineering variables that decide the outcome. Use the table below as a side-by-side reference during specification.

Comparison Item Standard (Slam) Check Valve Non-Slam Check Valve
Closing speed Closes late — disc only seats after reverse flow starts. Closes early and progressively with spring or damper assist.
Riesgo de golpe de ariete High — full reverse column impacts the seat. Very low — closing energy is absorbed by the mechanism.
Pump protection Limited; reverse flow and surge can reach the pump. Strong; reverse flow is shut off before it can return.
Operating noise Loud metallic slam on every stop. Quiet or near-silent closure.
Best-fit application Short, low-velocity lines, gravity flow, low duty cycle. Long pump-discharge lines, variable-speed pumps, high-rise risers, vertical lines.

See the five differences applied to your line?

Send us your pipe diameter, design flow and shutoff profile and we will return a side-by-side recommendation.

Compare slam vs non-slam for my line →

Cómo elegir la válvula de retención adecuada para su bomba

Not every line needs a non-slam valve. The right choice depends on how your system actually behaves in the moments after a pump stops. Use the two rules below as a quick gate before you spec.

Cuando una válvula de retención estándar es suficiente

A conventional swing or ball check valve will serve your business well when the discharge line is short, the flow velocity is modest (typically below 2 m/s), the pump is started and stopped infrequently, and the system has no vertical riser. In those cases the kinetic energy in the column is small, the surge pressure is tolerable, and the additional cost of a non-slam design is hard to justify.

Cuando necesitas un diseño que no se golpee

Move to a válvula de retención de cierre lento sin golpe whenever your line meets one or more of the following: long pump-discharge run (generally above a few hundred metres), high flow velocity (above ~2.5–3 m/s), a variable-speed or frequently-cycled pump, a vertical riser, a high-rise building water supply, or any service where downtime from a cracked seat is unacceptable. These are exactly the conditions in which a swing check valve will eventually hammer, and a non-slam design pays for itself in the first avoided shutdown.

Comprobación rápida de sobretensiones por golpe de ariete

For a first-pass estimate, the surge pressure from a sudden pump stop follows the Joukowsky equation: ΔP = ρ · a · ΔV, where ρ is fluid density, a is the pressure-wave speed (≈1,200 m/s for water in steel), and ΔV is the change in flow velocity.

Opciones de válvulas de retención antigolpes: tipos, materiales y conexiones

Across water-supply, HVAC, fire-protection and industrial plants, the non-slam category is usually specified across three axes: structure, body material, y end connection. Getting all three right is what separates a smooth-running line from a maintenance headache.

Estructura y función

For most pumping duties, the non-slam slow-closing check valve — a disc with an external or internal spring plus a hydraulic dashpot — is the go-to answer, because the dashpot lets the designer tune the closing time to the exact line length and velocity. Where weight, space or cost dominate, the dual-plate wafer design and the axial-flow silent check valve are the two common alternatives.

Materiales del cuerpo

Body material is driven by fluid, temperature, and external environment. The three families you will see on most data sheets are:

  • Hierro dúctil — the workhorse for clean water, raw water and sewage, typically with an internal epoxy coating for corrosion resistance.
  • Carbon steel — chosen for higher temperature or higher pressure water service, steam condensate, and industrial circulation lines.
  • Stainless steel — specified for potable water, food-grade, pharmaceutical, chemical and any media where iron pickup or external corrosion cannot be tolerated.

Conexiones finales

Two connection styles dominate. Brida bodies (EN 1092-2, ASME B16.5) are the default for pump rooms and above-ground plant piping because they are easy to install, align and maintain. Wafer bodies sit between flanges and are preferred where weight and face-to-face length matter — booster sets, skid packages, retrofits and large-diameter lines.

Ball Check Valve with full-bore internal design reduces clogging and allows solid particles to pass smoothly.

Ready to specify a non-slam check valve?

Browse the full non-slam, silent, dual-plate and slow-closing check valve range.

Browse the full check valve range →

Preguntas frecuentes

Is a slam check valve an actual product category?

No. “Slam check valve” is industry shorthand for a standard check valve (usually a swing type) that slams shut on flow reversal. There is no separate ASNI/EN classification for it — it describes a behaviour, not a design.

¿Cuál es la diferencia entre una válvula de retención silenciosa y una válvula de retención sin golpe?

A silent check valve targets fluid-borne noise via a streamlined axial flow path. A non-slam check valve targets closing impact and water hammer via early, spring- or damper-assisted closure. Some designs (e.g. spring-loaded axial-flow valves, damped slow-closing valves) achieve both, but when you specify, name the goal — noise, surge, or both.

¿Qué industrias utilizan más válvulas de retención antigolpes?

Estaciones municipales de suministro de agua y de refuerzo, elevadores de edificios de gran altura, circuitos de agua fría y caliente HVAC, líneas de protección contra incendios, grandes estaciones de bombeo de aguas residuales y de aguas residuales, agua de refrigeración de plantas de energía y sistemas de circulación industrial, en cualquier lugar donde se active una bomba y la línea de descarga sea larga, rápida o vertical.

¿Cómo puedo dimensionar una válvula de retención antigolpes para mi línea de bomba?

Tamaño por diámetro de línea (DN) para mantener la velocidad del flujo en el rango de 1,5 a 3,0 m/s; haga coincidir la clase de presión (PN10, PN16, Clase 150, etc.) con la presión de diseño de su sistema; y elija el rango de ajuste del tiempo de cierre de la compuerta según la longitud de la línea; las líneas más largas necesitan tiempos de cierre más largos y graduales.

¿Qué materiales y conexiones finales están disponibles?

Los materiales del cuerpo más comunes son hierro dúctil (para agua limpia y aguas residuales, generalmente con recubrimiento de epoxi), acero al carbono (para servicios de temperatura/presión más alta) y acero inoxidable (para medios potables, químicos y corrosivos). Las dos conexiones de los extremos dominantes son bridas (EN 1092-2/ASME B16.5) para uso general en plantas y tipo oblea para instalaciones compactas y livianas.

¿Se puede instalar verticalmente una válvula de retención antigolpes?

Sí, en líneas ascendentes (flujo ascendente), la mayoría de los diseños que no se cierran de golpe están clasificados para instalación vertical. Para flujo descendente, confirme con el fabricante que la guía del disco y el resorte están diseñados para esa orientación; no todos lo están.

Conclusión

A slam check valve is not a product — it is a behaviour your standard check valve is showing you every time a pump trips. The four non-slam structures (spring-assisted swing, dual-plate wafer, axial-flow/silent, and slow-closing damped) all solve the same problem in different ways: close early, close gently, and stop the water hammer before it cracks a seat or bursts a pipe. For most pumping systems above ~2.5 m/s, on long discharge runs, on vertical risers, or on variable-speed duty, the non-slam design is the cheaper answer in the long run — because the first avoided emergency shutdown pays for the valve.

Get a tailored non-slam check valve recommendation.

Ductile iron, carbon steel or stainless steel. Flanged or wafer. Engineered to your line, not a catalogue guess.

Request a quote →

Seraphinite AcceleratorOptimized by Seraphinite Accelerator
Turns on site high speed to be attractive for people and search engines.